Quenched and Tempered Steel Plates

Product Details:

140 ksi steel plate & 960 MPa is a high-strength, structural grade plate steel used in applications that require greater design strength. 140 ksi offers a higher min-yield (140 ksi) and tensile strength (142 ksi), combined with good toughness, excellent weldability and formability. It offers opportunities for weight reduction in some applications for increased payload in the finished unit.

Triton Alloys Inc distribution centers stock a solid supply of 140 ksi, which is most often used in the manufacture of heavy equipment such as haul trailers, crane booms, truck frames, logging and construction equipment, as well as design fabrications.

Product Details:

130 ksi min-yield steel plates are premium ultra-high strength, structural quality, heat-treated plates. Typical applications for these plates include highway trailers; forestry and mining equipment and any other uses where reduced weight combined with high strength are critical factors.Each producing mill has its own proprietary chemical composition and heat-treating process.Triton will gladly get mill specific specifications, which are available upon request.

The 130 minimum yield plates are used in many applications where weight can be reduced by using higher strength steel. These applications include crane booms, mining equipment and highway trailers. Mill certifications are available upon request.

Quenched and tempered steel plate Stock:

• 130 KSI Steel Plate
• 140 KSI Steel Plate
• A514 Steel Plate
• A710 Steel Plate
• TMCP 100 KSI Steel Plate
• RQT 701 Steel Plate
• S690QL1 Steel Plate
• S690QL Steel Plate
• S690Q Steel Plate
• S890QL1 Steel Plate
• S890QL Steel Plate
• S890Q Steel Plate
• S960QL Steel Plate
• S960Q Steel Plate
• Weldox 700
• WELTEN 780E

Product Details:

S960Ql is a high strength quenched and tempered, fine grained structural steel with a minimum yield strength of 960 MPa (140 ksi) in its delivery condition ex works. Its mechanical properties are achieved by water quenching followed by tempering.Weldox 960 is a high strength steel (960 MPa) that provides a unique combination of strength and toughness together with first-rate workshop properties. It is intended for load carrying structures with high demand on low weight.

Gr. S960QL is a High Yield Strength Structural Steel in the quenched and tempered condition which gives the material excellent strength. S960QL is a structural steel grade with an even greater yield strength than S890QLWeldox 960 meets the requirements of EN 10025 for the corresponding grades.

Chemical Properties Of s960ql steel plate:

Mechanical Properties Of s960ql steel plate:

Notch Impact Energy:

Product Details:

Triton Alloys Inc carries a stock of high yield cold forming steel plate with guaranteed mechanical properties, excellent cold formability, and a clean surface finish.The material is heat treated using the quench and temper process and has good bending and welding properties.

690QL1 is a high strength fine grained quenched and tempered structural steel. It has a minimum yield strength of 690 MPa. Known as Dillimax 690E  it is extra tough with minimum impact values down to -60 oC. S690QL1 has the steel number 1.8988 according to EN10025-6 and is available on an ex-stock basis in thicknesses from 6 mm to 250 mm.

S690QL1 is used for cranes, flood gates, bridges and many other applications where high strength is required with reduced weight and easy machinability. Given their high load capacity and risk reducing features S690QL1 can also reduce material and fabrication costs by 40% as a 33 mm plate of S690 can compare.

Chemical Properties Of s690ql1 steel plate:

Mechanical Properties Of s690ql1 steel plate:

Notch Impact Energy:

Product Details:

S890QL is a general structural steel that depending on thickness guarantees a minimum yield strength of up to 890 MPa. S890QL meets the requirements of EN 10025 for the corresponding grades. Typical applications are demanding load-bearing structures.This type of steel which is well over three times the strength of a basic S275 structural steel is still relatively easy to weld and fabricate. S890Q enables to make weight savings or support higher stresses and thus carry higher payload for lifting and transportation equipment.

S890Q is easy to machine, to bend and to weld which simplify production and maintenance. Depending on the thickness of the product and the manufacturing conditions.

Chemical Properties Of s890ql steel plate:

Mechanical Properties Of s890ql steel plate:

Notch Impact Energy:

Product Details:

A514 is a particular type of high strength steel, which is quenched and tempered alloy steel, with a yield strength of 100,000 psi (100 ksi or approximately 700 MPa). The ArcelorMittal trademarked name is T-1. A514 is primarily used as a structural steel for building construction. A517 is a closely related alloy that is used for the production of high-strength pressure vessels.

This is a standard set by the standards organization ASTM International, a voluntary standards development organizations that sets technical standards for materials, products, systems, and services.A514 plate steel has a min-yield strength of 100 ksi/690 MPa. It’s most commonly used as a structural steel in building construction, for cranes, or other large machines supporting high loads.

ASTM A514 alloy steel plate is known for its high yield strength, weldability, and toughness, even at low temperatures. It is a low carbon quenched and tempered alloy steel that is a low-cost, high performing material for structural use and high wear machine applications.

Chemical Properties Of A 514 steel plate:

Mechanical Properties Of A 514 steel plate:

Product Details:

Low-carbon A710 steel plate is an age hardening, alloy steel used where weight reduction, ease of fabrication and reduced welding costs are important. A710 is used in the manufacturing of jack-up rigs, construction equipment, pressure vessels, truck frames, piping components and shipbuilding.

This specification covers precipitation-strengthened low carbon nickel copper-chromium-molybdenum-columbium alloy structural steel plates. Precipitation strengthening and precipitation heat treatment shall be performed on the material to enhance and alter the required structural and mechanical properties. Heat analysis shall be used to determine the required chemical composition for carbon, manganese, phosphorus, sulfur, nickel, chromium, molybdenum, copper, columbium, and titanium. Yield strength, tensile strength, and elongation shall be evaluated using tension test and the required toughness shall be evaluated using notch toughness test.

Chemical Properties Of A 710 steel plate:

Mechanical Properties Of A 710 steel plate:

Product Details:

The mechanical properties introduced to the steel through this processing route are virtually equivalent to those obtained by heat treating conventionally rolled or forged steel. TMCP involves controlled hot working and microalloyed steel compositions.When TMCP is chosen as the process route, the rough steel section (i.e. the slab) is heated to a temperature regularly used for hot working operations (about 1200°C). The initial hot working (‘roughing’) is carried out in a normal fashion, but the final hot work reduction or ‘finishing pass’ is carried out at a lower temperature than would be used for older processes.

100 ksi/690 MPa steel plate is a high strength, steel plate produced using a Thermo Mechanically Controlled Process (TMCP). This process allows the plate to have a superior surface quality, excellent weldability, better forming and higher charpy values than Q & T plate.100KSI steel plate was developed for applications that require a high strength-to-weight ratio.  It has many of the same properties as A514 carbon steel plate, including high strength, machinability and weldability.  It is available as temper-leveled plate and sold under a variety of tradenames.  The most common tradename is Domex 100XF. 100KSI / 100XF has a 100,000 psi minimum yield and tensile strength.

Chemical Properties Of TMCP 100 ksi steel plate:

Mechanical Properties Of TMCP 100 ksi steel plate:

Product Details:

S890Q is a general structural steel that depending on thickness guarantees a minimum yield strength of up to 890 MPa. S890Q meets the requirements of EN 10025 for the corresponding grades. Typical applications are demanding load-bearing structures.This type of steel which is well over three times the strength of a basic S275 structural steel is still relatively easy to weld and fabricate.

We Triton alloys Inc find that the category of steel plate that S890QL falls into is called different things by different engineers. Plate of this types are described as below.s890q steel plate . Triton Alloys Inc carries one of the largest stocks of s890q steel plate in India

Chemical Properties Of s890q steel plate:

Mechanical Properties Of s890q steel plate:

Notch Impact Energy:

Product Details:

Triton Allos690ql-steel-plateys Inc carries a stock of high yield cold forming steel plate with guaranteed mechanical properties, excellent cold formability, and a clean surface finish.The material is heat treated using the quench and temper process and has good bending and welding properties.

S690 QL is a high yield structural steel grade produced in compliance with EN 10025:6:2004.

Due to the materials high strength nature, using S690QL will promote leaner designed structures with increased payload capacity and energy efficiency.and it is written down in a variety of ways such as: EN10025 S690QL, EN10025 S690 QL, EN 10025 S690QL, EN 10025 S690 QL

Chemical Properties Of s690ql steel plate:

Mechanical Properties Of s690ql steel plate:

Notch Impact Energy:

Product Details:

Weldox is Structural Steel plate from SSAB Sweden. Weldox 700 is a general structural steel with a minimum yield strength of 700 MPa. Weldox 700 meets the requirements for the corresponding steel grades and qualities according to EN 10025.

Weldox 700 is a high strength structural steel (700 MPa) with outstanding toughness for a multitude of load carrying structures and other applications. Leading features are uniform properties, easy to weld and possible to bend real tight.

Chemical Properties Of weldox 700 steel plate:

Mechanical Properties Of weldox 700 steel plate:

Product Details:

RQT® 701 is one of the grades in the RQT® range of high strength quenched and tempered structural steel manufactured by Tata Steel which is one of Europe’s largest steel makers. It is a steel that combines high yield and tensile strengths with good notch toughness and excellent weldability and has a minimum yield strength of 690 MPa. The steel is very similar in its properties to the European steel specification EN 10025 S690QL.

The steel has been developed for use in applications such as mining and quarrying, process industry, material handling, construction, and earth moving. Designers, engineers, and plant operators strive to reduce weight and increase the efficiency of equipment. There are significant benefits to be had by using high strength quenched and tempered steels for maximum structura performance in extreme working environments.

Chemical Properties Of rqt 701 steel plate:

Mechanical Properties Of rqt 701 steel plate:

Carbon equivalent values:

Product Details:

Triton Alloys are one of the prominent Domex High Tensile Steel Plates Supplier, Manufacturer & Exporters. Domex 700 MC IS Hot rolled, extra high strength, cold forming steel from SSAB Sweden. Domex cold forming steels are thermo-mechanically rolled in modern plants where the heating, rolling and cooling processes are carefully controlled. The chemical analysis, consisting of low levels of carbon and manganese has precise addition of grain refiners such as niobium, titanium or vanadium. This together with a clean structure, makes Domex Steels the most competitive alternative for cold formed and welded products. Domex 700 MC with designation D and E meet and exceed the demands for steel S700MC in EN-10149-2.

Domex 700 cool framing steels are thermo-mechanically come in current plants where the warming, moving and cooling procedures are painstakingly controlled. Domex 700 substance dissection, comprising of low levels of carbon and manganese has exact expansion of grain refiners, for example, niobium, titanium or vanadium. This together with a clean structure makes Domex Steels the most focused option for frosty framed and welded items.The additional high quality steel evaluations are utilized as a part of uses, for example, truck body, cranes and earth moving machines.

Domex 700 Plate Chemical Composition:

Domex 700 Plate Mechanical Properties:

Typical Application of Domex 700 Plate
The extra high strength steel grades are used in applications such as truck chassis, cranes and earthmoving machines. In these applications, the high strength of the steels is used to save weight and/or to increase the payload. As a result of this and the good formability of the steels, the total costs can be reduced.
The additional high quality steel evaluations are utilized as a part of uses, for example, truck body, cranes and earth moving machines. In these applications, the high quality of the steels is utilized to spare weight and/or to build the payload. As a consequence of this and the great formability of the steels, the aggregate expenses can be diminished. Normal applications are vehicle chassis, holder casing structures, steel extensions and building developments, chimney stack cases, rail wagons, snow sheds, various types of poles i.e. applications where a consumption safe steel is required together with high quality.
Also, this steel is climate safe, i.e. amid open air use inside several years, a smooth minimal oxide layer is framed that restrains further consumption. Domex 700 characterized by weldability, impact toughness, formability, high strength, corrosion resistance.

Product Details:

Quenched and tempered plate, a steel that is stronger and harder than ordinary carbon steel. The product is used for the manufacture and repair of machinery and structures where greater abrasion resistance or higher yield strength are required.

It is not uncommon in our industry to find the same type of steel plate given different names by different engineers.

Plates of this type are variously described as:

• High Strength Quenched and Tempered Steel Plate
• High Yield Quenched and Tempered Steel Plate
• High Strength Structural Steel Plate,
• High Yield Structural Steel Plate
• High Strength Low Alloy Steel Plate
• HSLA

This type of steel plate is used in the manufacture of cranes, forklifts, bridges, offshore fabrications, mining and quarrying equipment, mooring equipment, and vehicle chassis to name but a few applications.

Machining:

• The RQT range can be machined and drilled using high-speed steel or cemented carbide tools.  The approximate hardness of the RQT range can be obtained from the value of the ultimate tensile strength and falls within the range 240-280 BHN.

Welding:

• Care should be taken to avoidhydrogen cracking and there are many factors to take into consideration before welding.  Full technical guidance for welding is available from the sales/technical team at Triton alloys Co.

Technical Specifications:

Flame Cutting:

• RQT steels can be cut satisfactorily using conventional oxy-fuel gas practices, in many cases without the need for preheat, as long as cutting procedures take into account plate thicknesses and carbon equivalent values. Water jet, where no heat is generated, or plasma cutting can also be used. Care should be taken when cutting under water as the quenching effect could result in a high hardness edge forming.  With all thermal cutting processes care should be taken that cut edges are free from sharp notches.

Cold Bending:

• Quenched & Tempered steels can be readily cold formed however the power required will be higher (70%) than that for mild steel of the same thickness.  It is recommended that the largest possible bending radius should be used, and generally the inside radius should not be less that 3 times the plate thickness.

Weldability and Toughness:

Product Details:

Triton Allys Inc carries a stock of high yield cold forming steel plate with guaranteed mechanical properties, excellent cold formability, and a clean surface finish.The material is heat treated using the quench and temper process and has good bending and welding properties.

S690Q is high yield strength structural steels grade in the quenched and tempered.The symbol S is structural steel, 690 for the minimum yield strength in thickness under 50mm.The Symbol Q mean the delivery condition in quenched and tempered
S690q could be through the -20 temperature impact and the energy is 30J.

Triton could supply EN 10025-6 S690Q plates directly from our mill. Besides that, we also have stock in hand in large thickness.

Chemical Properties Of s690q steel plate:

Mechanical Properties Of s690q steel plate:





Quenched and tempered steel plate Stock:

• 130 KSI Steel Plate
• 140 KSI Steel Plate
• A514 Steel Plate
• A710 Steel Plate
• TMCP 100 KSI Steel Plate
• RQT 701 Steel Plate
• S690QL1 Steel Plate
• S690QL Steel Plate
• S690Q Steel Plate
• S890QL Steel Plate
• Weldox 700
• WELTEN 780E

Additional Information:

• Item Code: 7204
• Production Capacity: 2000 Metric Tons
• Delivery Time: Ready Stock
• Packaging Details: As per customer requirement .